Rocket Launcher, Radar Arch - Sr.Uni-Arch SHIPPING INCLUDED TO LOWER 48 STATE DESTINATIONS CALL FOR SHIPPING COST QUOTE TO LOCATIONS OUTSIDE THE LOWER 48 STATES Have a Pontoon Boat or need a large arch? Here it is. Great for large beamed boats and sail boats. Will hold all of your accessories, davits, solar panels, wind generators, or all of your fishing need. Our Sr. Uni Arch will span up an 11' beam. You can can our front visor, rod holders and other accessories a you see fit. Up to 84" of height and 125" wide. Mounts to floor or sides as necessary. Take a few minutes to look at the pictures below to get a better idea if this is the right arch for your boat. Corner braces strengthens this arch and makes it ready for any job. Select standoff option for increasing strength of side mounts. Unit weighs 125lbs. Lift capacity 300lbs #110 Very strong and usable unit. Built from 2" schedule 40 ANODIZED aluminum tube. Just like all of our arches, this arch is made to be used, not just for looks. Mount planner board reels, antennas, lights, outriggers and so on. Comes stock with 4 bolt on rod holders. Hollow tube all the way through to run and hide wires. You will need to drill an access hole near the bottom of one of the legs above the mounts approximate 1" above the top of the mounts when the mounts are fully seated in the tube and an exit hole near where you will be mounting your lights on the top cross tube. Insert a wire during assembly to serve as a cord for pulling the wires through the tube when the assembly is complete. We recommend using a good quality automotive anti-seize compound on all threads. While not mandatory this additional step will save you work later should you decide to move or disassemble rod holders etc. Two different style mounts "side and deck". Mounting holes are .278 diameter and are sized for 1/4 20 screws. Stainless steel screws are recommended. Also backing plates are recommended. You may need to cut small amounts of flotation foam under the gunnels on some boats. Assembly required. Bolts,nuts and lock washers for holding the bases to the deck or cabin side are not included due to the wide variety of hull and or cabin thicknesses. Purchase the stainless steel bolts, nuts, fender washers and lock washers locally. More terrific options for your arch, Click on the image or part no. below. 100-18 107 100-17 100-13 100-20 100-15 100-32 100-21 Captains Pkg 109 180 FOS-22 100-19 100-26 108-2x4 100-24 Captains Package upgrades to a total of = BRONZE Economy Package 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 1.91" clamps) 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 2.375" clamps) 1 Net Holder Part# 109 with 1.91" clamps SILVER Standard Package 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 1.91" clamps) 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 2.375" clamps) 1 Net Holder Part# 109 with 1.91" clamps 2 Quick Swivel Rod Holders RH with 1.91" Clamps 1 Light Bracket Set (2 light brackets) with 1.91" Clamps GOLD Premium Package 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 1.91" clamps) 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 2.375" clamps) 2 Net Holder Part# 109 with 1.91" clamps 2 Quick Swivel Rod Holders RH with 1.91" Clamps 1 Light Bracket Set 100-13 (2 light brackets) with 1.91" Clamps 2 Marine Lights 100-20 2 Cup/Drink Holders 100-17 with 1.91" Clamps 2 Universal Multi-Mounts 100-36 with 1.91" Clamps You can swap some items, however not all items have the same swap value. The rod holders, net holder, radar pad and light bracket set are even swaps, that means you can swap one for the other. There is a $15.00 up charge to swap one of the items included for a the swivel mount rod holder. NO RETURNS ON INTERNATIONAL ORDERS, DOMESTIC RETURNS RECEIVED IN AS NEW CONDITION ARE SUBJECT TO A 20% RESTOCKING FEE.
Great for large beamed boats and sail boats. Will hold all of your accessories, davits, solar panels, wind generators, or all of your fishing need.
Our Sr. Uni Arch will span up an 11' beam. You can can our front visor, rod holders and other accessories a you see fit. Up to 84" of height and 125" wide. Mounts to floor or sides as necessary. Take a few minutes to look at the pictures below to get a better idea if this is the right arch for your boat. Corner braces strengthens this arch and makes it ready for any job. Select standoff option for increasing strength of side mounts. Unit weighs 125lbs. Lift capacity 300lbs #110 Very strong and usable unit. Built from 2" schedule 40 ANODIZED aluminum tube. Just like all of our arches, this arch is made to be used, not just for looks. Mount planner board reels, antennas, lights, outriggers and so on. Comes stock with 4 bolt on rod holders. Hollow tube all the way through to run and hide wires. You will need to drill an access hole near the bottom of one of the legs above the mounts approximate 1" above the top of the mounts when the mounts are fully seated in the tube and an exit hole near where you will be mounting your lights on the top cross tube. Insert a wire during assembly to serve as a cord for pulling the wires through the tube when the assembly is complete. We recommend using a good quality automotive anti-seize compound on all threads. While not mandatory this additional step will save you work later should you decide to move or disassemble rod holders etc. Two different style mounts "side and deck". Mounting holes are .278 diameter and are sized for 1/4 20 screws. Stainless steel screws are recommended. Also backing plates are recommended. You may need to cut small amounts of flotation foam under the gunnels on some boats. Assembly required. Bolts,nuts and lock washers for holding the bases to the deck or cabin side are not included due to the wide variety of hull and or cabin thicknesses. Purchase the stainless steel bolts, nuts, fender washers and lock washers locally. More terrific options for your arch, Click on the image or part no. below. 100-18 107 100-17 100-13 100-20 100-15 100-32 100-21 Captains Pkg 109 180 FOS-22 100-19 100-26 108-2x4 100-24 Captains Package upgrades to a total of = BRONZE Economy Package 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 1.91" clamps) 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 2.375" clamps) 1 Net Holder Part# 109 with 1.91" clamps SILVER Standard Package 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 1.91" clamps) 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 2.375" clamps) 1 Net Holder Part# 109 with 1.91" clamps 2 Quick Swivel Rod Holders RH with 1.91" Clamps 1 Light Bracket Set (2 light brackets) with 1.91" Clamps GOLD Premium Package 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 1.91" clamps) 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 2.375" clamps) 2 Net Holder Part# 109 with 1.91" clamps 2 Quick Swivel Rod Holders RH with 1.91" Clamps 1 Light Bracket Set 100-13 (2 light brackets) with 1.91" Clamps 2 Marine Lights 100-20 2 Cup/Drink Holders 100-17 with 1.91" Clamps 2 Universal Multi-Mounts 100-36 with 1.91" Clamps You can swap some items, however not all items have the same swap value. The rod holders, net holder, radar pad and light bracket set are even swaps, that means you can swap one for the other. There is a $15.00 up charge to swap one of the items included for a the swivel mount rod holder.
Hollow tube all the way through to run and hide wires. You will need to drill an access hole near the bottom of one of the legs above the mounts approximate 1" above the top of the mounts when the mounts are fully seated in the tube and an exit hole near where you will be mounting your lights on the top cross tube.
Insert a wire during assembly to serve as a cord for pulling the wires through the tube when the assembly is complete.
We recommend using a good quality automotive anti-seize compound on all threads. While not mandatory this additional step will save you work later should you decide to move or disassemble rod holders etc.
Two different style mounts "side and deck". Mounting holes are .278 diameter and are sized for 1/4 20 screws. Stainless steel screws are recommended. Also backing plates are recommended. You may need to cut small amounts of flotation foam under the gunnels on some boats.
You can swap some items, however not all items have the same swap value. The rod holders, net holder, radar pad and light bracket set are even swaps, that means you can swap one for the other. There is a $15.00 up charge to swap one of the items included for a the swivel mount rod holder.
