Rocket Launcher/Rod Storage & Radar Arch Anodized UNI-Arch #140 SHIPPING INCLUDED TO LOWER 48 STATE DESTINATIONS CALL FOR SHIPPING COST QUOTE TO LOCATIONS OUTSIDE THE LOWER 48 STATES New polished anodized Uni Arch - Resistant to saltwater corrosion Fits most boats. Adjust from 50" up to 96" Wide. Up to 60" Tall. Comes with backing plates, break away mounting hardware and 4 bolt on adjustable rod holders. You can add bolt on rod holders and mount them where you need, just like the 4 stock ones. Or get the arch and ad extras later. Very strong and usable unit. Built from 2" schedule 40 aluminum tube. Just like all of our arches, this arch is made to be used, not just for looks. Mount planner board reels, antennas, lights, outriggers and so on. Designed to fold down in a matter of minutes. Hollow tube all the way through to run and hide wires. You will need to drill an access hole near the bottom of one of the legs above the mounts approximate 1" above the top of the mounts when the mounts are fully seated in the tube and an exit hole near where you will be mounting your lights on the top cross tube. Insert a wire during assembly to serve as a cord for pulling the wires through the tube when the assembly is complete. We recommend using a good quality automotive anti-seize compound on all threads. While not mandatory this additional step will save you work later should you decide to move or disassemble rod holders etc. Two different style mounts "side and deck". Mounting holes are .278 diameter and are sized for 1/4 20 screws. Stainless steel screws are recommended. Also backing plates are recommended. You may need to cut small amounts of flotation foam under the gunnels on some boats. When you pick an approximate width you will have 8" of adjustment in and out. If you have any questions please feel free to call 1-586-255-0212 Unit weighs 80lbs. Assembly required. Bolts,nuts and lock washers for holding the bases to the deck or cabin side are not included due to the wide variety of hull and or cabin thicknesses. Purchase the stainless steel bolts, nuts, fender washers and lock washers locally. More terrific options for your arch, Click on the image or part no. below. 100-18 107 100-17 100-13 100-20 100-15 100-32 100-21 Captains Pkg 109 180 FOS-22 100-19 100-26 108-2x4 100-24 Product images shown with options Product images shown with options Product images shown with options Captains Package upgrades to a total of = 8 Bolt on Rod Holders Part# 107 (4 come with your arch & 4 with Capt. Pkg) 1 Light Bracket Set Part# 100-13 2 Quick Swivel Rod Holders Part# 180 1 Net Holder Part# 109 You can swap some items, however not all items have the same swap value. The rod holders, net holder, radar pad and light bracket set are even swaps. There is a $15.00 up charge to swap one of the items included for a the swivel mount rod holder. Check with us if you want to swap items included in the captains package.
New polished anodized Uni Arch - Resistant to saltwater corrosion
Fits most boats. Adjust from 50" up to 96" Wide.
Up to 60" Tall.
Comes with backing plates, break away mounting hardware and 4 bolt on adjustable rod holders.
You can add bolt on rod holders and mount them where you need, just like the 4 stock ones. Or get the arch and ad extras later.
Very strong and usable unit. Built from 2" schedule 40 aluminum tube.
Just like all of our arches, this arch is made to be used, not just for looks. Mount planner board reels, antennas, lights, outriggers and so on.
Designed to fold down in a matter of minutes.
Hollow tube all the way through to run and hide wires. You will need to drill an access hole near the bottom of one of the legs above the mounts approximate 1" above the top of the mounts when the mounts are fully seated in the tube and an exit hole near where you will be mounting your lights on the top cross tube. Insert a wire during assembly to serve as a cord for pulling the wires through the tube when the assembly is complete. We recommend using a good quality automotive anti-seize compound on all threads. While not mandatory this additional step will save you work later should you decide to move or disassemble rod holders etc. Two different style mounts "side and deck". Mounting holes are .278 diameter and are sized for 1/4 20 screws. Stainless steel screws are recommended. Also backing plates are recommended. You may need to cut small amounts of flotation foam under the gunnels on some boats.
Hollow tube all the way through to run and hide wires. You will need to drill an access hole near the bottom of one of the legs above the mounts approximate 1" above the top of the mounts when the mounts are fully seated in the tube and an exit hole near where you will be mounting your lights on the top cross tube.
Insert a wire during assembly to serve as a cord for pulling the wires through the tube when the assembly is complete.
We recommend using a good quality automotive anti-seize compound on all threads. While not mandatory this additional step will save you work later should you decide to move or disassemble rod holders etc.
Two different style mounts "side and deck". Mounting holes are .278 diameter and are sized for 1/4 20 screws. Stainless steel screws are recommended. Also backing plates are recommended. You may need to cut small amounts of flotation foam under the gunnels on some boats.
When you pick an approximate width you will have 8" of adjustment in and out.
If you have any questions please feel free to call 1-586-255-0212
Unit weighs 80lbs.
Assembly required. Bolts,nuts and lock washers for holding the bases to the deck or cabin side are not included due to the wide variety of hull and or cabin thicknesses. Purchase the stainless steel bolts, nuts, fender washers and lock washers locally.
You can swap some items, however not all items have the same swap value. The rod holders, net holder, radar pad and light bracket set are even swaps. There is a $15.00 up charge to swap one of the items included for a the swivel mount rod holder.
