THE FISHING SEASON IS JUST A FEW WEEKS AWAY, BE SURE TO ORDER BEFORE THE RUSH. CURRENT LEAD TIME FOR ARCHES IS 2 TO 3 WEEKS-ORDER NOW!!!!
FISHING TOWERS, SKI AND RADAR ARCHES: SCROLL DOWN
NOT TO WORRY YOU CAN INSTALL AN ARCH ON YOUR BOAT AND WE WILL HELP YOU FROM START TO FINISH. GOT QUESTIONS ? GIVE US A CALL OR TEXT AT 586-255-0212
SCROLL DOWN THIS PAGE TO VIEW OUR GREAT SELECTION OF ARCHES AND ACCESSORIES.
ABSOLUTE BEST VALUE AND GREAT AFTERMARKET ARCHES FOR YOUR BOAT PAGE DOWN TO VIEW THEM. IF YOUR SERIOUS ABOUT AN ARCH YOUR IN THE RIGHT PLACE, CONTINUE READING BELOW.
SHIPPING INCLUDED TO LOWER 48 STATE DESTINATIONS
BEST AFTERMARKET ARCHES ON THE MARKET TODAY. SCROLL DOWN TO VIEW OUR ARCHES AND OTHER ACCESSORIES. NOW IS A GREAT TIME TO UPGRADE YOUR BOAT WITH A FISHING/RADAR ARCH.
LEAD TIME IS 1-2 WEEKS FOR MOST PRODUCTS! IF YOUR IN A HURRY CALL/TEXT BEFORE ORDERING!
ARCHES ARE THE WAY TO GO!! GET THE MOST OUT OF YOUR BOAT - WE HAVE ARCHES BUILT FOR TUBING, WAKE-BOARDING, WAKE-SURFING, SKIING AND MORE. NOW IS A GREAT TIME TO ORDER YOUR ARCH.
FISHING, RADAR, SKI ARCHES, WAKE-BOARDS & T TOPS
Order now! - Need help ordering your arch ? Just give us a call 1-586-255-0212
It's a simple process 1. Measure across the boat to your potential mounting points, 2.) Measure to ensure you have sufficient clearance above your Bimini (you need approximately 3 Inches of clearance). Write down the measurements. Select Deck/Gunnel or Side/Cuddy Mount. Measure once more to be sure. We offer 2" narrow mounting pads in case you have limited room on your gunnel. See the bottom of this page for information on Powder Coating your arch.
DO NOT RELY ON THE PRODUCT IMAGES ALONE, FEEL FREE TO ASK AS MANY QUESTIONS AS NEEDED. MEASURE CAREFULLY RESTOCK FEES MAY APPLY ON RETURNS (see notes at the bottom of this page)
STILL HAVE QUESTIONS.TELL US ABOUT YOUR BOAT OR SEND US A PICTURE OF YOUR BOAT AND WE CAN RECOMMEND AN ARCH THAT WORKS WITH YOUR VESSEL
We have arches for every boat!!! Easily install these excellent quality, super strong, durable fishing, radar & wake board or ski arches with common household tools. Built with 2 inch schedule 40 anodized aluminum. We have the best prices too. All of our arches and our t-top fold down with minimal effort for storage or passing under bridges.
Our arches work well on most aluminum river boats such as Bentz Boats, Koffler Boats, Alumaweld, Hewescraft, Bratt Jet, Rogue, RiverPro, RiverHawk, Thunderjet, Boulton, North River, Weldcraft, KingFisher, Lund, Alumacraft, Starcraft and Rockproof Boats, just to name a few. If you are interested in one of our arches just give us a call 586-255-0212
A FEW HOURS OF YOUR TIME WILL SAVE YOU A LOT OF $$$
You can order your arch now and add accessories later which gives you a chance to see which accessories you need/want on the arch.
Always a great time to add an arch to your boat! Don't waste your money and time on a custom arch, our arches are as good or better than custom arches. Arches can be laid down to get your boat under bridges or in the garage. All screws and hardware are Stainless Steel. Click here for Spreader and Boat Flood Light. The Captains Package is a great value offered on many of our arches. The best value fishing and radar arches on the market today. Most are in stock and can ship out in 1 to 2 days. Add one to your cart. you deserve it, your boat deserves it and your family will love it !!!
Maximize the free space on your deck. Store rods, add grab handles, navigation and flood lights, radar pads, cup holders, net holders, antennas and much more. Pull skiers or wake boarders with our FOS-320 Jr.River Cross Over Arch. or add Tigress Clamp On Outriggers to your T-Top.
Note: Clamp Size should not be larger than the tube you are clamping to, typically it should be slightly less than the outside diameter of the tube you are clamping to. Slightly less than is usually best.
Measure twice and write down the results.
Tips for wiring your arch or t-top are at the bottom of this page.
Side mount arches may require access on the interior side of the cabin or gunnel. You can use deck plate panels if needed to cover cut out holes when installing backing plates where holes need to be cut.
FREE SHIRT WITH $600 ORDER
CLICK ON YOUR SELECTION BELOW FOR DETAILS!
If you are going to powder coat your arch here is an article regarding that process.
Q. We are having problems with powder coating adhesion on parts that are anodized prior to powder coating. Are there any inherent problems with powder coating over anodized aluminum parts? Is it better (or possible) to anodize after powder coating? S. P.
A. Parts that have been anodized can be powder coated successfully with certain precautions. First the aluminum has to be cleaned after anodizing using at least DI water to remove salts or complete cleaning using a three-stage cleaning process to remove hand prints and soils accumulated during shipment and storage.
The three-stage process should be a cleaner/coater followed by a rinse and a DI rinse. If the part is very clean, then the powder coating will have good adhesion. Of course, the powder has to be applied evenly to an appropriate film thickness (1.5–3.0 mils) and fully cured to provide good surface wet-out and adhesion. You can forget about anodizing after powder coating, as this is impossible.
TIPS FOR RUNNING WIRES IN YOUR ARCH OR T TOP
The wires will not go through the deck/side mounts, the mounts are solid and they fold down so you need to all for that when you run the wires. Your wires will need to come up/out near the mount and the wires will go through a hole you will drill in the arch tube 2" inches above the bottom of the tube ensuring you are above the point where the mounts are fully inserted in the tube, the hole should not be larger than 1/2".
Now run/fish the wires to the point/s you want the wires to exit, drill the exit hole on the bottom side of the tube.
If you plan to fold the arch down to the rear drill the bottom hole in the rear leg. Leave some slack or use marine grade connectors to detach and avoid stretching or breaking the wiring. Use grommets in the holes you drill. If possible run wiring as you assemble the arch or include a line to pull the wires to the exit point.
RODHOLDERDEPOT.COM IS YOUR FISHING ARCH SUPERSTORE
Clamps are designed not slip so they do not close all the way to form a true circle, they are slightly oval, clamp size should be slightly smaller than the outside diameter of your pipe or tube. Example on in the chart above 1.903" is for aluminum tube OD of 2" or roughly 95.5% of the OD.
The table below gives the outside diameter of Pipe. You need to know if you are measuring pipe or tube. The following link will help you understand the difference. Click here for details
Actual Pipe Outside Diameter Inches
Fractional Pipe O.D. (Approximate) Pipe Circumference Actual Pipe Outside Diameter mm 1 3/4 in-p 1.050 1-1/16" 3-5/16" 26.7 2 1 in-p 1.315 1-5/16" 4-1/8" 33.4 3 1 1/4 in-p 1.660 1-21/32" 5-7/32" 42.2 4 1 1/2 in-p 1.900 1-7/8" 5-31/32" 48.3 5 2 in-p 2.375 2-3/8" 7-15/32" 60.3
PIPE SIZE : 1.050", 26 mm O.D. Schedule 40: 0.824" I.D., 0.113" Wall 1" IPS
PIPE SIZE: 1.315", 33mm O.D. Schedule 40: 1.049" I.D., 0.133" Wall 1-1/4" IPS
PIPE SIZE: 1.660", 42 mm O.D. Schedule 40: 1.380" I.D., 0.140" Wall 1-1/2" IPS
PIPE SIZE: 1.900", 48mm O.D. Schedule 40: 1.610" I.D., 0.145" Wall 2" IPS
PIPE SIZE: 2.375", 60mm O.D. Schedule 40: 2.067" I.D., 0.154" Wall
For your protection on Large Dollar orders we may require photo ID
RESTOCKING FEES: Products returned that are not defective will be subject to a restocking charge of up to 20% of the purchase price of the item being returned. Most returned items cannot be sold as new, they require repackaging, inspection and are generally discounted because the package has been opened. This In addition to the lost labor of packaging, inspection, and paperwork etc. in processing the original purchase. As a customer you generally do not purchase items that you can see have been opened.